| PCI Express Mini/mPCIe bus series |
* PCI card plugged into connector figure
Attention:
1. Whole signals of bus Test Socket/Converter/Extender maybe not 100% one to one(1:1)
convert, please check specification.
2. No matter how many Slot/Socket on our board, PCI Express series only can use one
Slot/Socket at a time.
3. All Converters/Test Socket/Riser card/Extender have Timing, Delay, Impedance,
Resistance Contact problem, so we can't guarantee can work 100%.
4. External converter card, if occur unreliable, try to shorten the cable length will be more stable.
(Discontinued) |
||
|
 |
 Mechanical Drawing |
CV09Pe-mPe1 PCI Express to Mini PCI Express Converter (Discontinued)
CV09Pe-mPe1h Half-Mini Card Converter (Discontinued)
CV09Pe-mPe1v1.1 PCI Express to Mini PCI Express Converter
CV09Pe-mPe1hv1.1 Half-Mini Card Converter
v1.1
the PETP0, PETN0, PERP0, PERN0, REFCLK+, REFCLK- signals
can be modified with a Solder Pads.
1. Insert Converter card into Desktop motherboard, for PCI Express Mini Card test,
can avoid the inconvenience to use NoteBook motherboard.
2. The 52pin socket is 4.6mm height, and the PCB with two bare,
easy to measure Mini Card Front/Back side signals.
3. LED inductor : 3.3V, 1.5V, WAN, LAN, PAN
4. +mSK2= Dual Mini PCI Express socket.
5. Schematics:
 |
 |
 |
 |
 |
SH09Pe-mPe2 PCI Express to Mini PCI Express card
SH09Pe-mPe2h Half-Mini Card
1. Insert Converter card into Desktop motherboard, for PCI Express Mini Card test,
can avoid the inconvenience to use NoteBook.
2. The 52pin socket is 4.6mm height, and parts of PCB with bare,
easy to measure Mini Card Front/Back side signals.
3. LED inductor : 12V, 3.3V, 3.3Vaux, 1.5V, WAN, LAN, PAN, PERST, WAKE, WDIS.
4. +NF= add Switch for PCI Express bus power supply(12V, 3.3V, 3.3Vaux, 1.5V) ON-OFF,
can execute Mini card hot swapping and hot plugging test in Power-On,
don't use force to swapping and plugging to avoid equipment damage.
Run the hot swapping and hot plugging card in operation system,
must write PCI Express device configuration register's Read-Writer program.
5. +mSK2= Dual Mini PCI Express socket.
6. Schematics:
SH09Pe-emPe2 PCI Express external Mini PCI Express card
SH09Pe-emPe2h Half-Mini Card
1. External type from motherboard for testing, Form Factor: 2U, 3U, 4U
2. attached one 15cm and one 30cm cable
(Option: length= 45cm or order different length of Flat cable to match buyer's request)
* For external type converter card, to short the length of cable if unstable.
3. +NF= add Switch for PCI Express bus power supply(12V, 3.3V, 3.3Vaux, 1.5V) ON-OFF,
can execute Mini card hot swapping and hot plugging test in Power-On,
don't use force to swapping and plugging to avoid equipment damage.
Run the hot swapping and hot plugging card in operation system,
must write PCI Express device configuration register's Read-Writer program.
4. +Pe= add PCI Express slot SH09mPe-T6(Target adapter)
5. +mSK2= Dual Mini PCI Express socket.
6. Schematics:
Photo Zoom + (Discontinued) |
(Discontinued) |
 |
CV09Pe-mPeNF simple mPCIe hot swapping and hot plugging converter (Discontinued)
CV09Pe-mPeNFh Half-Mini Card (Discontinued)
1. Switch Mini PCI Express bus power source(+3.3v, +1.5v) ON-OFF,
Mini card can be inserted in Power-ON to do test, but must carefully to avoid signal or
power shortage and equipment damage.
2. LED inductor : 12V, 5V, 3.3V, 1.5V, WAN, LAN, PAN, WDIS, PRST, WAKE
3. Run real hot plugging function in operation system,
must write PCI Express device configuration register Read-Writer program.
4. Option: +5V= Add one set 12V to 5V DC converter.
5. Option: +U= Add USB connector x2, without USB function,
only for power source +5V input or output.
6. Schematics:
 (Discontinued) |
CV09Pe-eMPe PCI Express external to Mini PCI Express Converter Card(Discontinued)
CV09Pe-eMPeh Half-Mini Card(Discontinued)
1. Insert Converter card into Desktop motherboard, for PCI Express Mini Card test,
can avoid the inconvenience to use NoteBook motherboard.
2. The 52pin socket is 4.6mm height, and the PCB with two bare,
easy to measure Mini Card Front/Back side signals.
3. LED inductor : 12V, 5V, 3.3V, 1.5V, WAN, LAN, PAN, WDIS, PRST, WAKE
4. with cable length= 30cm
5. Schematics:
|
 |
 |
 |
|
 |
 |
 |
|
 |
 |
 |
|
 |
 |
 |
|
 |
 |
 |
|
(Discontinued) |
 (Discontinued) |
 |
|
|
|||
User can choose to combine the Base adapter, Target adapter, except the
CV09mPe-B1, CV09mPe-B2, the others can be modified to suit for Half-Mini Card.
Base adapter: CV09mPe-B1, CV09mPe-B2, CV09mPe-B3(Discontinued),
CV09mPe-B3v1.1, CV09mPe-B3v1.2,
CV09mPe-B4, CV09mPe-B5
Target adapter: CV09mPe-T1, SH09mPe-T1v2, CV09mPe-T2,
SH09mPe-T3, SH09mPe-T3v2, CV09mPe-T4, CV09mPe-T5, SH09mPe-T6
* 52pin socket with 4.6mm height, one part of PCB is bare,
easy to measure the whole Front/Back side signals of Mini Card.
CV09mPe-Pe Full mPCIe to PCIe converter(Discontinued)
CV09mPeh-Pe Half mPCIe to PCIe converter(Discontinued)
CV09mPe-PeL(Solder
side up),
CV09mPeh-PeL
CV09mPe-PeLv2(Solder side up), CV09mPeh-PeLv2
CV09mPe-PeR(Component side up), CV09mPeh-PeR
1. Can use this converter to insert PCI Express card into Mini PCI Express bus.
2. Use the attached Cable A, in order to input 12V power source for PCI Express bus.
3. LED inductor: 5V, 12V signal LED display.
4. +PH= add 40p Pin Head, in order to measure the Mini PCI Express bus signals.
5. +U= add USB connector and Cable B, in order to input 5V power source for USB.
6. Schematics:
CV09mPe-B4 x2 + Cable: mPCIe Gold Finger external Gold Finger
 |
 |
|
 |
|
 |
 |
 |
 |
 |
CV09mPe-S1 Full mPCIe protector adapter
1a. Use this protector adapter to protect motherboard's Mini PCI Express 52p socket.
CV09mPe-S1h Full to Half protector card
1b. Use this protector card to change Full-Mini Card Form to Half-Mini Card Form.
2. LED inductor: 1.5V, GND(=3.3V) signal LED display.
3. +NF= add Switch for Mini PCI Express bus power supply ( 3.3V, 1.5) ON-OFF,
can execute Mini PCI Express card hot swapping and plugging test in Power-On,
don't use force to swapping and plugging to avoid equipment damage.
* Run the hot swapping and hot plugging card in operation system,
must write PCI Express device configuration register's Read-Writer program.
4. +U= add USB connector x2 and Cable B, in order to input 5V USB power source,
but only can choose one USB connector to use.
5. +mSK2= Dual Mini PCI Express socket.
6. Schematics:
CV09mPe-S2 Full mPCIe protector adapter
1a. Use this protector adapter to protect motherboard's Mini PCI Express 52p socket.
CV09mPe-S2h Full to Half protector adapter
CV09mPe-S2hv2 Full to Half protector adapter
1b. Use this protector adapter to change Full-Mini Card Form to Half-Mini Card Form.
CV09mPeh-S2 Half to Full protector adapter
1c. Use this protector adapter to change Half-Mini Card Form to Full-Mini Card Form.
2. LED inductor: 5V signal LED display.
3. +U= add USB connector and Cable B, in order to input 5V power source for USB.
4. Schematics:
CV09mPe-L(Left side) Full mPCIe protector adapter
1a. Use this protector adapter to protect motherboard's Mini PCI Express 52p socket,
Mini Card insert from Left side.
CV09mPe-Lh Full to Half protector adapter
1b. Use this protector adapter to change Full-Mini Card Form to Half-Mini Card Form.
CV09mPe-R(Right side) Full mPCIe protector adapter
1c. Use this protector adapter to protect motherboard's Mini PCI Express 52p socket,
Mini Card insert from Right side.
CV09mPe-Rh Full to Half protector adapter
1d. Use this protector adapter to change Full-Mini Card Form to Half-Mini Card Form.
2. LED inductor: 1.5V, GND(=3.3V) signal LED display.
3. +NF= add Switch for Mini PCI Express bus power source(3.3v, 1.5v) ON-OFF,
can test Mini card in Power-ON(simple hot swapping and hot plugging card),
but must carefully to avoid signal or power shortage and equipment damage.
Run the hot swapping and hot plugging card in operation system,
must write PCI Express device configuration register's Read-Writer program.
4. +U= add USB connector x2 and Cable B, in order to input 5V USB power source,
but only can choose one USB connector to use.
5. +mSK2= Dual Mini PCI Express socket.
6. Schematics:
 |
 |
 |
CV09mPe-ePe1 Mini PCI Express external PCI Express card
1. External type card from Mini PCI Express bus outside to normal PCI Express card.
2. if PCI Express slot use 12V power source, must DIY solder on SH09mPe-T6.
3. LED inductor : 1.5V, GND(=3.3V), 12V.
4. attached one 15cm and one 30cm cable
(Option: length= 45cm or order different length of Flat cable to match buyer's request)
* For external type converter card, to short the length of cable if unstable.
5. +NF= add Switch for Mini PCI Express bus power source(3.3v, 1.5v) ON-OFF,
can test Mini card in Power-ON(simple hot swapping and hot plugging card),
but must carefully to avoid signal or power shortage and equipment damage.
Run the hot swapping and hot plugging card in operation system,
must write PCI Express device configuration register's Read-Writer program.
6. +U= add USB connector and Cable B, for input 5V power source to USB.
7. Schematics:
CV09mPe-ePe2 Mini PCI Express external PCI Express card
1. External type card from Mini PCI Express bus outside to normal PCI Express card.
2. if PCI Express slot use 12V power source, must DIY solder on SH09mPe-T6.
3. LED inductor : 1.5V, GND(=3.3V), 5V, 12V.
4. attached one 15cm and one 30cm cable
(Option: length= 45cm or order different length of Flat cable to match buyer's request)
* For external type converter card, to short the length of cable if unstable.
5. Schematics:
 |
|
 |
 |
CV09mPe-e1 Mini PCI Express external Mini PCI Express adapter
CV09mPe-e1h Full to Half external adapter
1. The Mini Card in external type for testing.
2. LED inductor: 1.5V, GND(=3.3V) signal LED display.
3. with cable length= 45cm(Option: length= 30cm or any Flat cable length)
* External converter card, if occur unreliable, try to shorten the cable length will be more stable.
4. +NF= add Switch for Mini PCI Express bus power supply ( 3.3V, 1.5) ON-OFF,
can execute Mini PCI Express card hot swapping and plugging test in Power-On,
don't use force to swapping and plugging to avoid equipment damage.
* Run the hot swapping and hot plugging card in operation system,
must write PCI Express device configuration register's Read-Writer program.
5. +U= add USB connector x2 and Cable B, in order to input 5V USB power source,
but only can choose one USB connector to use.
6. +mSK2= Dual Mini PCI Express socket.
7. Schematics:
CV09mPe-e2 Mini PCI Express external Mini PCI Express adapter
CV09mPe-e2h Full to Half external adapter
CV09mPeh-e2 Half to Full external adapter
CV09mPeh-e2h Half to Half external adapter
1. The Mini Card in external type for testing.
2. LED inductor: 1.5V, GND(=3.3V) signal LED display.
3. with cable length= 45cm(Option: length= 30cm or any Flat cable length).
* External converter card, if occur unreliable, try to shorten the cable length will be more stable.
4. +U= add USB connector and Cable B, in order to input 5V power source for USB,
5. +mSK2= Dual Mini PCI Express socket.
6. Schematics:
 |
 |
mSK2 Dual Mini PCI Express socket
1. For one Mini PCI Express Gold Fingers to two Mini PCI Express socket,
can use one Half-Mini card and one Full-Mini card.
2. Must be from another PCIe slot(socket) DIY connection PERN0/PERP0/PETN0/PETP0 signal.
3. Schematics:
| Home | Index |   |
Start: 01/08/2002 Update: 02.01.2012
