Q&A:6 2007.1. 25 > We are interested in a design that could allow us to insert 

PCI cards into our current ISA embedded NetMan based on the AMD Elan chip.

Is the PCI to ISA bridge possible in such a configuration?

Reply:  

to use our products PCI to ISA bridge card, please pay more attention about follow, 

as this series product not a complete item, must complete it for yourself.

1.You must have the ISA card's hardware detail information.

2.You must be a professional Firmware/Hardware engineer.

3.Because we only offer the bridge card, the others driver and software must do it for 

your-self. For products, all details description please view our website,

Ev71p.htm or Ev72p.htm

Q&A:5 2007.1. 24 > to convert PCI-X (64-bit/100MHz 3.3Vol ) to standard PCI 

and the same slot (PCI-X) to ISA?

Reply: 

Because we do not have the same equipment  with you, therefore can not to know what's  

your need exactly, you must decide by yourself for following items, and to use this series 

products,

1. You must make sure your system support 5V Tolerant,

it seems can work in theory, but must try it for yourself in practice.

2. The details about products please view website CV09P3-5VSv2x1 and SH08PS

Q&A:4 2007.1.17> I would like to order sample for CV11R-240+184(DDR+DDR2)

 and would like to know clearly that both slots (on mainboard) ddr and ddr2 can be 

tested using this tester

Reply: 

because too many circuits between mother board and DRAM Module,

so if mother board dead,  CV11R-240+184 shall test circuits open-short at first 

(not test Module), it's helpful for repair motherboard.

Q&A:3 2006.12.15> we are looking for Post-Card for testing Motherboard and Notebook.

Could you please provide us information for this kind of products?

Reply: 

for your inquiry, please view our website of CV-0x series products,

Q&A:2 2006.11.22> We are looking for a Mini-PCI converter to standard PCI slot, 

we only need for it to have one PCI slot, and it is planned to be used with a Viewcast 

Osprey 440 capture card with an HP laptop. Your device CV09MPv4-P1 seems to be 

an adequate device but its fixings to the laptop are solid, can this be supplemented with 

a ribbon/teflon like connecter to allow for it to bend and be a little further away?

Reply: 

1. Whole signals of PCI bus Converter/Extender maybe not 100% one to one(1:1) 

convert, please check specification.

2. All Converters/Riser card/Extender have Timing, Delay, Impedance,

Resistance Contact  problem, so we can't  guarantee can work100%.

3. External converter card, if occur unstable, try to shorten the cable to better this status.

products details please view website CV09eMP-eP1v4 and CV09eMP-eP

Q&A:1 2006.6.05 > Is this to put pci expressx16 on port pci expressx1?

Reply: 

the model is SH08PE1v2-16S(x1 PCB + x16 Slot)

Attention for PCIe series product, before you buy it:

1. Whole signals of PCIe bus Test Socket/Converter/Extender maybe 

not 100% one to one(1:1) convert, please check specification.

2. All Converters/Test Socket/Riser card/Extender have Timing, Delay, Impedance, 

Resistance Contact  problem, so we can't  guarantee can work100%.

3. External converter card, if occur unstable, try to shorten the cable to better this status.

4. Down-plugging and Up-plugging must depends on your mother board and add-in 

card which PCI Express Lane of bandwidth and routed.

Home

Index

Start: 5/6/2006 Update: 09.29.2009